Changing the Settings
16
Setting the SYSTEM Parameters
The following parameters allow you to make the system settings for
KSP-100.
Room Acoustic Control
For more information, see “Compensating for the Room Acoustics
(Room Acoustic Auto Control)” (p. 10).
Output EQ > FRONT-L, FRONT-R, SUR-L, SUR-R, CENTER
Parameter Value Explanation
Low Cut Freq.
Flat,
20.0 Hz–1.00 kHz
Low-cut frequency
EQ Type PEQ, GEQ Select EQ type
Output EQ > FRONT-L, FRONT-R, SUR-L, SUR-R, CENTER >
EQ (EQ Type = GEQ)
Parameter Value Explanation
Switch O, On EQ switch
BAND 1 Gain -12 dB–+12 dB Gain
:
BAND 15 Gain -12dB–+12 dB Gain
Output EQ > FRONT-L, FRONT-R, SUR-L, SUR-R, CENTER >
EQ (EQ Type = PEQ)
Parameter Value Explanation
Switch O, On EQ switch
BAND 1 Type Shelving, Peaking Filter type
BAND 1 Freq. 20.0 Hz–20.0 kHz Frequency
BAND 1 Gain -12 dB–+12 dB Gain
BAND 1 Q 0.3–16
Bandwidth. Higher values make
the band narrower.
BAND 2 Freq. 20.0 Hz–20.0 kHz Frequency
BAND 2 Gain -12 dB–+12 dB Gain
BAND 2 Q 0.3–16
Bandwidth. Higher values make
the band narrower.
:
BAND 15 Q 0.3–16
Bandwidth. Higher values make
the band narrower.
Output EQ > SUBWOOFER
Parameter Value Explanation
Low Cut Type
6 dB Butter–
24 dB Link-R
Low-cut lter type
Low Cut Freq.
Flat,
20.0 Hz–1.00 kHz
Low-cut frequency
High Cut Type
6 dB Butter–
48 dB Link-R
High-cut lter type
High Cut Freq. 35.0 Hz–2.00 kHz High-cut frequency
Delay Time 0.0 ms–50.0 ms Delay time
Output EQ > SUBWOOFER > EQ
Parameter Value Explanation
Switch O,On EQ switch
BAND1 Type Shelving, Peaking Filter type
BAND1 Freq. 20.0 Hz–20.0 kHz Frequency
BAND1 Gain -12 dB–+12 dB Gain
BAND1 Q 0.3–16
Bandwidth. Higher values make the
band narrower.
BAND2 Freq. 20.0 Hz–20.0 kHz Frequency
BAND2 Gain -12 dB–+12 dB Gain
BAND2 Q 0.3–16
Bandwidth. Higher values make the
band narrower.
BAND3 Freq. 20.0 Hz–20.0 kHz Frequency
BAND3 Gain -12 dB–+12 dB Gain
BAND3 Q 0.3–16
Bandwidth. Higher values make the
band narrower.
BAND4 Type Shelving, Peaking Filter type
BAND4 Freq. 20.0 Hz–20.0 kHz Frequency
BAND4 Gain -12 dB–+12 dB Gain
BAND4 Q 0.3–16
Bandwidth. Higher values make the
band narrower.
Output EQ > SUBWOOFER > Compressor
Parameter Value Explanation
Switch O, On Compressor switch
Attack 0–100 Speed at which compression starts.
Release 0–100
Time from when the volume falls
below the threshold level until
the compressor eect is no longer
applied.
Threshold 0–100
Volume level at which compression
begins.
Ratio
1.00:1–16.0:1,
Inf:1
Compression ratio
Post Gain 0 dB–+18 dB Output gain
Output Level 0–100 Output level
Anti-Feedback
Parameter Value Explanation
Diuse Level O, 1–5
Slightly modulates the pitch
of the MIC input to suppress
unwanted acoustic feedback.
Dynamic Filter
Switch
O, On
Anti-Feedback switch.
When set to “On,” the KSP-100
detects sudden acoustic
feedback and suppresses it.
Dynamic Filter
Release
0–16
Amount of time the anti-
feedback eect is maintained
For more information, see “Preventing Acoustic Feedback (Static
Anti-Feedback)” (p. 12).
Comments to this Manuals