BMB KSP-100 Owner's Manual download pdf (Page 13)

Changing the Settings

Parameter Value Explanation

MIC Direct Level 0–100 MIC direct level

MIC1/2, MIC3/4

Parameter Value Explanation

Input Level Mute, -63.0 dB–0.0 dB Input level

Low Cut Freq. Flat, 20.0 Hz–1.00 kHz Low cut frequency

EQ Type PEQ, GEQ Select EQ type

MIC1/2, MIC3/4 > Noise Suppressor

Parameter Value Explanation

Switch O, On Noise Suppressor switch

Threshold 0–100

Volume at which noise

suppression begin.

Release 0–100

Time from when noise

suppression begins until the

volume reaches zero.

MIC1/2, MIC3/4 > Compressor

Parameter Value Explanation

Switch O, On Compressor switch

Attack 0–100

Speed at which compression

starts.

Release 0–100

Time from when the volume

falls below the threshold level

until the compressor eect is

no longer applied.

Threshold 0–100

Volume level at which compres-

sion begins.

Ratio 1.00:1–16.0:1, Inf:1 Compression ratio

Post Gain 0 dB–+18 dB Output gain

Output Level 0–100 Output level

MIC1/2, MIC3/4 > EQ (EQ Type = GEQ)

Parameter Value Explanation

Switch O, On EQ switch

BAND1 Gain -12 dB–+12 dB Gain

BAND15 Gain -12 dB–+12 dB Gain

MIC1/2, MIC3/4 > EQ (EQ Type = PEQ)

Parameter Value Explanation

Switch O, On EQ switch

BAND1 Type Shelving, Peaking Filter type

BAND1 Freq. 20.0 Hz–20.0 kHz Frequency

BAND1 Gain -12 dB–+12 dB Gain Gain

BAND1 Q 0.3–16

Bandwidth. Higher values make

the band narrower.

BAND2 Freq. 20.0 Hz–20.0 kHz Frequency

BAND2 Gain -12 dB–+12 dB Gain Gain

BAND2 Q 0.3–16

Bandwidth. Higher values make

the band narrower.

BAND15 Q 0.3–16

Bandwidth. Higher values make

the band narrower.

Echo

Parameter Value Explanation

Delay Level 0–100 Delay output level

Delay Type

Digital Delay,

Tape Echo

Delay type

Reverb Level 0–100 Reverb output level

Press the buttons shown below to change the settings of the KSP-100. See the following pages for more information.

Setting Operation Page

MIC Parameters Press the [MIC] button. p. 13

MUSIC Parameters Press the [MUSIC] button. p. 15

OUTPUT Parameters Press the [OUTPUT] button. p. 15

SYSTEM Parameters Press the [MIC] + [MUSIC] (SYSTEM) buttons. p. 16

For information on the relationship between the parameters and signal ow, see “Block Diagram” (p. 19).

MEMO

Noise Suppressor

Parameter Value Explanation

Switch O, On Noise Suppressor switch

Threshold 0–100

Volume at which noise

suppression begin.

For parameters shown with a gray background (prexed by in

the display), you can move the cursor to that parameter and press

the [ENTER] button to access advanced settings.

* However, the advanced setting screen will not appear if the

setting is “O.”

Press the [EXIT] button to go back to the previous screen.

Setting the MIC Parameters

1 2 ... 8 9 10 11 12 13 14 15 16 17 18 ... 21 22

Comments to this Manuals

No comments

BMB KSP-100 Owner's Manual Page 13

Comments to this Manuals

Related products and manuals for Karaoke systems BMB KSP-100